Solutions · Building management
Every chiller, lift and genset maintained — and the whole building in view
One place for the building engineering team: preventive maintenance, requests from the floors, live equipment monitoring, alarms and energy — for office towers, malls, hospitals, hotels and apartments.
- PM by date or running hours
- Requests become work orders
- Energy per meter
- BACnet/IP, Modbus, MQTT
Live building data
Real equipment, live readings
Measured by the equipment every few seconds, on every screen and phone — not typed into a log sheet
Live · BACnet/IP
Live · BACnet/IP · Modbus
Live · ModbusPhotos: Unsplash. Readings are sample data.
SCADA for buildings
The whole building, live — in 2D and 3D
Drawn in the AssetGrid designers and bound to BACnet/IP, Modbus and MQTT points — no code
Floors take the colour of their temperature, so a hot floor stands out before a tenant calls.
Equipment in alarm changes colour on the 2D screen and in 3D, with the reading right beside it.
Saved views and a tour mode run the 3D view on a wall screen; one tap opens the 2D screen of any plant.
The same screens run in the Android app for technicians on their rounds.
What building engineering teams deal with every day
Tenants notice every minute of downtime — the team needs to see problems first
Chillers, pumps, lifts and gensets run around the clock. When one fails, every tenant feels it within minutes.
Filter changes, lift inspections and genset runs slip when the schedule lives on paper and in one person's head.
“AC not cold on floor 12” arrives in a chat group, gets buried, and nobody can say when it was fixed.
Air conditioning is usually the largest share of a building's electricity, yet few teams see it per system or per floor.
What AssetGrid does for your building
Maintenance, requests, monitoring and energy on one set of asset data
Preventive maintenance
PM that follows the calendar — and the running hours
Plan every recurring job once. AssetGrid raises the work order when it falls due and keeps the history for audits and insurance.
- Schedules by date (monthly AHU filters, yearly lift inspection) or by running hours (genset service every 250 hours)
- Running hours counted from the equipment's run signal — no hand-written log
- Checklists for recurring tests: weekly fire pump run, genset load test, panel inspection
- A QR label on every asset: scan it with the phone to see its history and open a work order
Requests & work orders
From a complaint to a closed work order, on record
Every request has an owner, a priority and a due time, and the building manager can see what is open on which floor.
- Building staff raise a request from the web or the phone, with a photo and the location
- The engineering team approves it and turns it into a work order with a priority and a due time
- Technicians work from the Android app: checklist, photos, parts used and sign-off
- Contractors and their parts and services tracked through vendors and purchase orders
Live monitoring & alarms
See the plant room before someone calls
Read the values that matter from chiller controllers, VFDs, genset controllers, power meters and sensors, and act on them.
- Alarm limits with on-call escalation by e-mail and in the app when nobody acknowledges
- Condition rules and anomaly detection catch slow drifts, like a chiller working harder for the same load
- Draw the chiller plant or a floor plan in the screen designer, or show the building in 3D, bound to live values
- Every value kept as history for trends and reports
Energy
Know where every kWh goes
Connect the power meters you already have and see consumption, cost and CO₂ for each one.
- Consumption, cost and CO₂ per meter, from its kWh counter
- Compare the chiller plant, AHUs, lifts, lighting and tenant floors by hour, day or month
- Excel export for the monthly report to the building owner
Every system in the building, in one asset register
Organised by building, tower, floor and room — each asset with its QR label, history, PM plan and spare parts
- Chillers & cooling towers
- AHU, FCU & VAV
- Pumps & booster sets
- Lifts & escalators
- Gensets & ATS
- Transformers, LVMDP & panels
- UPS & batteries
- Fire pumps & sprinklers
- Water tanks, WTP & STP
- CCTV, access & BMS panels
Example
Chiller 2 trips at 02:10 — what happens next
Spotted, escalated, fixed and on record before the morning shift
- 01
Signal
The chiller controller's trip and condenser pressure reach AssetGrid through the collector.
- 02
Alarm & escalation
The on-call HVAC technician is alerted; if nobody acknowledges in time, it escalates to the chief engineer.
- 03
Work order
A corrective work order opens on CH-02 with its history, checklist and spare parts.
- 04
On site
The technician scans the chiller's QR code, follows the checklist and records parts and photos.
- 05
Closed & learned
Downtime and the fix are on record; the next similar fault shows what worked last time.
Works with the equipment the building already has
A small collector on the building network reads the points you choose — your BMS keeps controlling
Read analog, binary and multi-state points straight from the BMS and its controllers: chillers, AHUs, VAVs, FCUs.
Power meters, VFDs, genset and chiller controllers, and RS-485 devices through a Modbus TCP gateway.
IoT sensors and gateways: temperature, humidity, CO₂, water leaks and tank levels.
Plant-room PLCs and SCADA servers that publish their data over OPC UA.
See AssetGrid with your building's equipment
Start with the asset register, PM and requests on web and Android, then connect chillers, meters and gensets when you are ready. Every building is scoped and quoted on its own.
Questions from building teams
Does AssetGrid replace our BMS?
No. Your BMS keeps controlling air conditioning and lighting. AssetGrid reads the values you choose, raises alarms and work orders, and runs maintenance, requests, spare parts and energy reporting around it.
Can it read our BACnet system?
Yes. The collector reads BACnet/IP points from the BMS and its controllers, and you choose which ones to monitor. AssetGrid reads; your BMS keeps controlling.
Can we start with maintenance only?
Yes. Many teams start with the asset register, PM schedules, checklists and requests on web and Android, and connect equipment later.
We manage several towers. Does that work?
Yes. Buildings, towers, floors and rooms are locations, so assets, requests and reports can be filtered down to a single floor.
Do technicians need a computer?
No. Technicians and building staff use the Android app: scan QR codes, follow checklists, add photos and close work orders.